欢迎您访问程序员文章站本站旨在为大家提供分享程序员计算机编程知识!
您现在的位置是: 首页  >  后端开发

lnmp之php-fpm+nginx+ulimit的综合设置之故障排除

程序员文章站 2022-05-09 16:04:06
...
相信其它的地方大家都懂,这里重点说下面粗体注释标注部分 参数设置必须与系统的 ulimit -Sn 参数一致,并且 php-fpm.conf,nginx,conf中的设置要一致,否则会出现诸多历史遗留问题以及不和谐的ERROR WRING问题
以下是nginx.conf里的一些 配置信息,重点说红色部分
#user  nobody;user www www;worker_processes  auto;#add by Happy; set the value == system's ulimit -sn 's value
#############################################worker_rlimit_nofile 65535;############################################
error_log  logs/error.log;#error_log  logs/error.log  notice;#error_log  logs/error.log  info;pid        logs/nginx.pid;events {    # set by Happy; set the value == system's "ulimit -sn" is value    # if use is epoll,the worker_connections 65535+1  but sys's ulimit -sn == 65536
############################################    worker_connections 65535;
############################################
    multi_accept  on;    use  epoll;}http {    include       mime.types;    default_type  application/octet-stream;    # add by Happy 2014-04-18    server_names_hash_bucket_size  128;    client_header_buffer_size      32K;    large_client_header_buffers    4 32k;    # set user upload size    client_max_body_size           8m;    # add end     log_format  main  '$remote_addr - $remote_user [$time_local] "$request" '                      '$status $body_bytes_sent "$http_referer" '                      '"$http_user_agent" "$http_x_forwarded_for"';    access_log  logs/access.log main;    #display nginx version add this,    #but you have set fastcgi.conf set     #fastcgi_param SERVER_SOFTWARE nginx/$nginx_version;    #fastcgi_param SERVER_SOFTWARE nginx;    #this is by Happy set for 2014-04-19    server_tokens off;    sendfile       on;    #tcp_nopush     on;    tcp_nopush	   on;    tcp_nodelay    on;    #add by Happy 2014-04-19    fastcgi_connect_timeout    300;    fastcgi_send_timeout       300;    fastcgi_read_timeout       300;    fastcgi_buffer_size        64k;    fastcgi_buffers         4  64k;    fastcgi_busy_buffers_size  128k;    fastcgi_temp_file_write_size  128k;    #keepalive_timeout  0;    keepalive_timeout  60;    client_header_timeout  10;    client_body_timeout  10;    #reset_timeout_connection  on;    send_timeout  10;    #set one ip link num and memory    limit_conn_zone $binary_remote_addr zone=addr:5m;    limit_conn addr 100;    #open gzip by Happy    gzip  on;    gzip_disable      "msie6";    gzip_proxied      any;    gzip_min_length   1k;    gzip_buffers      4  16k;    #if you set squid2.x,please set 1.0    #by Happy set 2014-04-19    gzip_http_version 1.1;     gzip_comp_level   4;    gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript;    gzip_vary        on;    ## add by Happy,set 2014-04-23    #xian zhi dan ge IP  bing fa wei 10 ge    limit_conn_zone  $binary_remote_addr zone=happy:10m;    limit_conn happy 20;    #xian zhi lian jie su du, da yu 1m de wen jian xian su 100k/s    #if you user's one link down file's size > 1M,the set user one down is 100k/S    limit_rate_after 1m;    limit_rate       200k;    #open_file_cache max=100000 inactive=60s;    #open_file_cache_valid 65s;    #open_file_cache_min_uses 2;    #open_file_cache_errors off;    server {        listen       80 default;        server_name  www.xxxx.cn xxx.cn;	#charset  utf-8;        access_log  logs/host.access.log;        location / {	            #root   html;	    root   /home/var/www;	    index  index.php index.html index.htm;	    if (!-e $request_filename) {	    	rewrite ^(.*) /index.php last;	    }	}        location ~* \.(?:gif|ico|jpe?g|png|swf|bmp|swf)$ {            expires 30d;            log_not_found off;            ## No need to bleed constant updates. Send the all shebang in one            #            #    fell swoop.            #            tcp_nodelay off;            #            #    Set the OS file cache.            #            open_file_cache max=1000 inactive=120s;            open_file_cache_valid 125s;            open_file_cache_min_uses 2;            open_file_cache_errors off;	    root /home/var/www;            #        }        location ~* \.(js|css)$ {            expires   1d;            root /home/var/www;        }	#error_page  404              /404.html;        # redirect server error pages to the static page /50x.html        #        error_page   500 502 503 504  /50x.html;        location = /50x.html {            root   html;        }        # proxy the PHP scripts to Apache listening on 127.0.0.1:80        #        #location ~ \.php$ {        #    proxy_pass   http://127.0.0.1;        #}        # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000        #        location ~ \.php$ {	    #root   html;            root           /home/var/www;            if (!-e $request_filename) {                rewrite (.*) /index.php last;	    }	    fastcgi_pass   127.0.0.1:9000;            fastcgi_index  index.php;            #fastcgi_param  SCRIPT_FILENAME  /scripts$fastcgi_script_name;            fastcgi_param  SCRIPT_FILENAME  $document_root$fastcgi_script_name;	    include        fastcgi_params;        }        # deny access to .htaccess files, if Apache's document root        # concurs with nginx's one        #        location ~ /\.ht {            deny  all;        }	location ~*\.(html|log|sh|bash)?$ {	    return 403;	}        location ~ ^/home/var/www/MVC/ {            deny  all;            break;        }        #return 500;	    }    # another virtual host using mix of IP-, name-, and port-based configuration    #    #server {    #    listen       8000;    #    listen       somename:8080;    #    server_name  somename  alias  another.alias;    #    location / {    #        root   html;    #        index  index.html index.htm;    #    }    #}    # HTTPS server    #    #server {    #    listen       443;    #    server_name  localhost;    #    ssl                  on;    #    ssl_certificate      cert.pem;    #    ssl_certificate_key  cert.key;    #    ssl_session_timeout  5m;    #    ssl_protocols  SSLv2 SSLv3 TLSv1;    #    ssl_ciphers  HIGH:!aNULL:!MD5;    #    ssl_prefer_server_ciphers   on;    #    location / {    #        root   html;    #        index  index.html index.htm;    #    }    #}}

PHP-FPM中的rlimit_files参数设置需同系统参数一致且同nginx 里的connections,rlimit参数相呼应,否则大流量并发下会出现如5xx,4xx等意象不到的错误状态

(这里只说红色粗体部分,其它的日后再解,相信大家一定也都懂得其它参数的设置)

;;;;;;;;;;;;;;;;;;;;;; FPM Configuration ;;;;;;;;;;;;;;;;;;;;;;; All relative paths in this configuration file are relative to PHP's install; prefix (/usr/local/php). This prefix can be dynamically changed by using the; '-p' argument from the command line.; Include one or more files. If glob(3) exists, it is used to include a bunch of; files from a glob(3) pattern. This directive can be used everywhere in the; file.; Relative path can also be used. They will be prefixed by:;  - the global prefix if it's been set (-p argument);  - /usr/local/php otherwise;include=etc/fpm.d/*.conf;;;;;;;;;;;;;;;;;;; Global Options ;;;;;;;;;;;;;;;;;;;[global]; Pid file; Note: the default prefix is /usr/local/php/var; Default Value: none;default disabled,show 2014-04-18 by Happypid = run/php-fpm.pid; Error log file; If it's set to "syslog", log is sent to syslogd instead of being written; in a local file.; Note: the default prefix is /usr/local/php/var; Default Value: log/php-fpm.log;default disabled,show 2014-04-18 by Happyerror_log = log/php-fpm.log; syslog_facility is used to specify what type of program is logging the; message. This lets syslogd specify that messages from different facilities; will be handled differently.; See syslog(3) for possible values (ex daemon equiv LOG_DAEMON); Default Value: daemon;syslog.facility = daemon; syslog_ident is prepended to every message. If you have multiple FPM; instances running on the same server, you can change the default value; which must suit common needs.; Default Value: php-fpm;syslog.ident = php-fpm; Log level; Possible Values: alert, error, warning, notice, debug; Default Value: notice;default disabled,show 2014-04-18 by Happylog_level = notice; If this number of child processes exit with SIGSEGV or SIGBUS within the time; interval set by emergency_restart_interval then FPM will restart. A value; of '0' means 'Off'.; Default Value: 0;emergency_restart_threshold = 0; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated.  This can be useful to work around; accidental corruptions in an accelerator's shared memory.; Available Units: s(econds), m(inutes), h(ours), or d(ays); Default Unit: seconds; Default Value: 0;emergency_restart_interval = 0; Time limit for child processes to wait for a reaction on signals from master.; Available units: s(econds), m(inutes), h(ours), or d(ays); Default Unit: seconds; Default Value: 0;default disabled,show 2014-04-18 by Happy ;process_control_timeout = 0; The maximum number of processes FPM will fork. This has been design to control; the global number of processes when using dynamic PM within a lot of pools.; Use it with caution.; Note: A value of 0 indicates no limit; Default Value: 0; process.max = 128; Specify the nice(2) priority to apply to the master process (only if set); The value can vary from -19 (highest priority) to 20 (lower priority); Note: - It will only work if the FPM master process is launched as root;       - The pool process will inherit the master process priority;         unless it specified otherwise; Default Value: no set; process.priority = -19; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging.; Default Value: yes;hou tai zhixing php-fpm default disabled,show 2014-04-18 by Happydaemonize = yes ; Set open file descriptor rlimit for the master process.; Default Value: system defined value;rlimit_files = 1024 ; Set max core size rlimit for the master process.; Possible Values: 'unlimited' or an integer greater or equal to 0; Default Value: system defined value;rlimit_core = 0; Specify the event mechanism FPM will use. The following is available:; - select     (any POSIX os); - poll       (any POSIX os); - epoll      (linux >= 2.5.44); - kqueue     (FreeBSD >= 4.1, OpenBSD >= 2.9, NetBSD >= 2.0); - /dev/poll  (Solaris >= 7); - port       (Solaris >= 10); Default Value: not set (auto detection);events.mechanism = epoll; When FPM is build with systemd integration, specify the interval,; in second, between health report notification to systemd.; Set to 0 to disable.; Available Units: s(econds), m(inutes), h(ours); Default Unit: seconds; Default value: 10;systemd_interval = 10;;;;;;;;;;;;;;;;;;;;; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;;; Multiple pools of child processes may be started with different listening; ports and different management options.  The name of the pool will be; used in logs and stats. There is no limitation on the number of pools which; FPM can handle. Your system will tell you anyway :); Start a new pool named 'www'.; the variable $pool can we used in any directive and will be replaced by the; pool name ('www' here)[www]; Per pool prefix; It only applies on the following directives:; - 'slowlog'; - 'listen' (unixsocket); - 'chroot'; - 'chdir'; - 'php_values'; - 'php_admin_values'; When not set, the global prefix (or /usr/local/php) applies instead.; Note: This directive can also be relative to the global prefix.; Default Value: none;prefix = /path/to/pools/$pool; Unix user/group of processes; Note: The user is mandatory. If the group is not set, the default user's group;       will be used.user = wwwgroup = www; The address on which to accept FastCGI requests.; Valid syntaxes are:;   'ip.add.re.ss:port'    - to listen on a TCP socket to a specific address on;                            a specific port;;   'port'                 - to listen on a TCP socket to all addresses on a;                            specific port;;   '/path/to/unix/socket' - to listen on a unix socket.; Note: This value is mandatory.listen = 127.0.0.1:9000; Set listen(2) backlog.; Default Value: 65535 (-1 on FreeBSD and OpenBSD);listen.backlog = 65535; Set permissions for unix socket, if one is used. In Linux, read/write; permissions must be set in order to allow connections from a web server. Many; BSD-derived systems allow connections regardless of permissions. ; Default Values: user and group are set as the running user;;                 mode is set to 0666;default disabled ,show 2014-04-18 by Happylisten.owner = wwwlisten.group = wwwlisten.mode = 0666;2014-04-18 shown END ; List of ipv4 addresses of FastCGI clients which are allowed to connect.; Equivalent to the FCGI_WEB_SERVER_ADDRS environment variable in the original; PHP FCGI (5.2.2+). Makes sense only with a tcp listening socket. Each address; must be separated by a comma. If this value is left blank, connections will be; accepted from any ip address.; Default Value: any;default disabled,show 2014-04-18 by Happylisten.allowed_clients = 127.0.0.1; Specify the nice(2) priority to apply to the pool processes (only if set); The value can vary from -19 (highest priority) to 20 (lower priority); Note: - It will only work if the FPM master process is launched as root;       - The pool processes will inherit the master process priority;         unless it specified otherwise; Default Value: no set; priority = -19; Choose how the process manager will control the number of child processes.; Possible Values:;   static  - a fixed number (pm.max_children) of child processes;;   dynamic - the number of child processes are set dynamically based on the;             following directives. With this process management, there will be;             always at least 1 children.;             pm.max_children      - the maximum number of children that can;                                    be alive at the same time.;             pm.start_servers     - the number of children created on startup.;             pm.min_spare_servers - the minimum number of children in 'idle';                                    state (waiting to process). If the number;                                    of 'idle' processes is less than this;                                    number then some children will be created.;             pm.max_spare_servers - the maximum number of children in 'idle';                                    state (waiting to process). If the number;                                    of 'idle' processes is greater than this;                                    number then some children will be killed.;  ondemand - no children are created at startup. Children will be forked when;             new requests will connect. The following parameter are used:;             pm.max_children           - the maximum number of children that;                                         can be alive at the same time.;             pm.process_idle_timeout   - The number of seconds after which;                                         an idle process will be killed.; Note: This value is mandatory.pm = dynamic; The number of child processes to be created when pm is set to 'static' and the; maximum number of child processes when pm is set to 'dynamic' or 'ondemand'.; This value sets the limit on the number of simultaneous requests that will be; served. Equivalent to the ApacheMaxClients directive with mpm_prefork.; Equivalent to the PHP_FCGI_CHILDREN environment variable in the original PHP; CGI. The below defaults are based on a server without much resources. Don't; forget to tweak pm.* to fit your needs.; Note: Used when pm is set to 'static', 'dynamic' or 'ondemand'; Note: This value is mandatory.pm.max_children = 30; The number of child processes created on startup.; Note: Used only when pm is set to 'dynamic'; Default Value: min_spare_servers + (max_spare_servers - min_spare_servers) / 2pm.start_servers = 12; The desired minimum number of idle server processes.; Note: Used only when pm is set to 'dynamic'; Note: Mandatory when pm is set to 'dynamic';pm.min_spare_servers = 1 1.5G set 2,2G set 2 2014-04-18 BY Happypm.min_spare_servers = 4; The desired maximum number of idle server processes.; Note: Used only when pm is set to 'dynamic'; Note: Mandatory when pm is set to 'dynamic';default pm.max_spare_servers = 3, 1.5G set 8,2G set 10 by 2014-04-18 by Happypm.max_spare_servers = 20; The number of seconds after which an idle process will be killed.; Note: Used only when pm is set to 'ondemand'; Default Value: 10s;pm.process_idle_timeout = 10s; ; The number of requests each child process should execute before respawning.; This can be useful to work around memory leaks in 3rd party libraries. For; endless request processing specify '0'. Equivalent to PHP_FCGI_MAX_REQUESTS.; Default Value: 0;default disabled set 500,show 2014-04-18 by Happypm.max_requests = 1000; The URI to view the FPM status page. If this value is not set, no URI will be; recognized as a status page. It shows the following informations:;   pool                 - the name of the pool;;   process manager      - static, dynamic or ondemand;;   start time           - the date and time FPM has started;;   start since          - number of seconds since FPM has started;;   accepted conn        - the number of request accepted by the pool;;   listen queue         - the number of request in the queue of pending;                          connections (see backlog in listen(2));;   max listen queue     - the maximum number of requests in the queue;                          of pending connections since FPM has started;;   listen queue len     - the size of the socket queue of pending connections;;   idle processes       - the number of idle processes;;   active processes     - the number of active processes;;   total processes      - the number of idle + active processes;;   max active processes - the maximum number of active processes since FPM;                          has started;;   max children reached - number of times, the process limit has been reached,;                          when pm tries to start more children (works only for;                          pm 'dynamic' and 'ondemand');; Value are updated in real time.; Example output:;   pool:                 www;   process manager:      static;   start time:           01/Jul/2011:17:53:49 +0200;   start since:          62636;   accepted conn:        190460;   listen queue:         0;   max listen queue:     1;   listen queue len:     42;   idle processes:       4;   active processes:     11;   total processes:      15;   max active processes: 12;   max children reached: 0;; By default the status page output is formatted as text/plain. Passing either; 'html', 'xml' or 'json' in the query string will return the corresponding; output syntax. Example:;   http://www.foo.bar/status;   http://www.foo.bar/status?json;   http://www.foo.bar/status?html;   http://www.foo.bar/status?xml;; By default the status page only outputs short status. Passing 'full' in the; query string will also return status for each pool process.; Example: ;   http://www.foo.bar/status?full;   http://www.foo.bar/status?json&full;   http://www.foo.bar/status?html&full;   http://www.foo.bar/status?xml&full; The Full status returns for each process:;   pid                  - the PID of the process;;   state                - the state of the process (Idle, Running, ...);;   start time           - the date and time the process has started;;   start since          - the number of seconds since the process has started;;   requests             - the number of requests the process has served;;   request duration     - the duration in µs of the requests;;   request method       - the request method (GET, POST, ...);;   request URI          - the request URI with the query string;;   content length       - the content length of the request (only with POST);;   user                 - the user (PHP_AUTH_USER) (or '-' if not set);;   script               - the main script called (or '-' if not set);;   last request cpu     - the %cpu the last request consumed;                          it's always 0 if the process is not in Idle state;                          because CPU calculation is done when the request;                          processing has terminated;;   last request memory  - the max amount of memory the last request consumed;                          it's always 0 if the process is not in Idle state;                          because memory calculation is done when the request;                          processing has terminated;; If the process is in Idle state, then informations are related to the; last request the process has served. Otherwise informations are related to; the current request being served.; Example output:;   ************************;   pid:                  31330;   state:                Running;   start time:           01/Jul/2011:17:53:49 +0200;   start since:          63087;   requests:             12808;   request duration:     1250261;   request method:       GET;   request URI:          /test_mem.php?N=10000;   content length:       0;   user:                 -;   script:               /home/fat/web/docs/php/test_mem.php;   last request cpu:     0.00;   last request memory:  0;; Note: There is a real-time FPM status monitoring sample web page available;       It's available in: ${prefix}/share/fpm/status.html;; Note: The value must start with a leading slash (/). The value can be;       anything, but it may not be a good idea to use the .php extension or it;       may conflict with a real PHP file.; Default Value: not set ;pm.status_path = /status ; The ping URI to call the monitoring page of FPM. If this value is not set, no; URI will be recognized as a ping page. This could be used to test from outside; that FPM is alive and responding, or to; - create a graph of FPM availability (rrd or such);; - remove a server from a group if it is not responding (load balancing);; - trigger alerts for the operating team (24/7).; Note: The value must start with a leading slash (/). The value can be;       anything, but it may not be a good idea to use the .php extension or it;       may conflict with a real PHP file.; Default Value: not set;ping.path = /ping; This directive may be used to customize the response of a ping request. The; response is formatted as text/plain with a 200 response code.; Default Value: pong;ping.response = pong; The access log file; Default: not set;access.log = log/$pool.access.log; The access log format.; The following syntax is allowed;  %%: the '%' character;  %C: %CPU used by the request;      it can accept the following format:;      - %{user}C for user CPU only;      - %{system}C for system CPU only;      - %{total}C  for user + system CPU (default);  %d: time taken to serve the request;      it can accept the following format:;      - %{seconds}d (default);      - %{miliseconds}d;      - %{mili}d;      - %{microseconds}d;      - %{micro}d;  %e: an environment variable (same as $_ENV or $_SERVER);      it must be associated with embraces to specify the name of the env;      variable. Some exemples:;      - server specifics like: %{REQUEST_METHOD}e or %{SERVER_PROTOCOL}e;      - HTTP headers like: %{HTTP_HOST}e or %{HTTP_USER_AGENT}e;  %f: script filename;  %l: content-length of the request (for POST request only);  %m: request method;  %M: peak of memory allocated by PHP;      it can accept the following format:;      - %{bytes}M (default);      - %{kilobytes}M;      - %{kilo}M;      - %{megabytes}M;      - %{mega}M;  %n: pool name;  %o: output header;      it must be associated with embraces to specify the name of the header:;      - %{Content-Type}o;      - %{X-Powered-By}o;      - %{Transfert-Encoding}o;      - ....;  %p: PID of the child that serviced the request;  %P: PID of the parent of the child that serviced the request;  %q: the query string ;  %Q: the '?' character if query string exists;  %r: the request URI (without the query string, see %q and %Q);  %R: remote IP address;  %s: status (response code);  %t: server time the request was received;      it can accept a strftime(3) format:;      %d/%b/%Y:%H:%M:%S %z (default);  %T: time the log has been written (the request has finished);      it can accept a strftime(3) format:;      %d/%b/%Y:%H:%M:%S %z (default);  %u: remote user;; Default: "%R - %u %t \"%m %r\" %s";access.format = "%R - %u %t \"%m %r%Q%q\" %s %f %{mili}d %{kilo}M %C%%" ; The log file for slow requests; Default Value: not set; Note: slowlog is mandatory if request_slowlog_timeout is set; if you open slowlog(man cha xun rizhi),the slowlog path is set;by Happy;slowlog = log/$pool.log.slowslowlog = /usr/local/php/var/log/php-slow.log; The timeout for serving a single request after which a PHP backtrace will be; dumped to the 'slowlog' file. A value of '0s' means 'off'.; Available units: s(econds)(default), m(inutes), h(ours), or d(ays); Default Value: 0;if you php thread time > the time,write php bad log;by Happy 2014-04-20request_slowlog_timeout = 2s ; The timeout for serving a single request after which the worker process will; be killed. This option should be used when the 'max_execution_time' ini option; does not stop script execution for some reason. A value of '0' means 'off'.; Available units: s(econds)(default), m(inutes), h(ours), or d(ays); Default Value: 0;if you php thread time > the time,close  the php script thread ;by Happy 2014-04-20request_terminate_timeout = 30s ; Set open file descriptor rlimit.; Default Value: system defined value;set the value === system ulimit -Sn 65535 
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;rlimit_files = 65535
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 ; Set max core size rlimit.; Possible Values: 'unlimited' or an integer greater or equal to 0; Default Value: system defined value;rlimit_core = 0 ; Chroot to this directory at the start. This value must be defined as an; absolute path. When this value is not set, chroot is not used.; Note: you can prefix with '$prefix' to chroot to the pool prefix or one; of its subdirectories. If the pool prefix is not set, the global prefix; will be used instead.; Note: chrooting is a great security feature and should be used whenever ;       possible. However, all PHP paths will be relative to the chroot;       (error_log, sessions.save_path, ...).; Default Value: not set;chroot =  ; Chdir to this directory at the start.; Note: relative path can be used.; Default Value: current directory or / when chroot;chdir = /var/www ; Redirect worker stdout and stderr into main error log. If not set, stdout and; stderr will be redirected to /dev/null according to FastCGI specs.; Note: on highloaded environement, this can cause some delay in the page; process time (several ms).; Default Value: no;catch_workers_output = yes; Clear environment in FPM workers; Prevents arbitrary environment variables from reaching FPM worker processes; by clearing the environment in workers before env vars specified in this; pool configuration are added.; Setting to "no" will make all environment variables available to PHP code; via getenv(), $_ENV and $_SERVER.; Default Value: yes;clear_env = no; Limits the extensions of the main script FPM will allow to parse. This can; prevent configuration mistakes on the web server side. You should only limit; FPM to .php extensions to prevent malicious users to use other extensions to; exectute php code.; Note: set an empty value to allow all extensions.; Default Value: .php;security.limit_extensions = .php .php3 .php4 .php5 ; Pass environment variables like LD_LIBRARY_PATH. All $VARIABLEs are taken from; the current environment.; Default Value: clean env;env[HOSTNAME] = $HOSTNAME;env[PATH] = /usr/local/bin:/usr/bin:/bin;env[TMP] = /tmp;env[TMPDIR] = /tmp;env[TEMP] = /tmp; Additional php.ini defines, specific to this pool of workers. These settings; overwrite the values previously defined in the php.ini. The directives are the; same as the PHP SAPI:;   php_value/php_flag             - you can set classic ini defines which can;                                    be overwritten from PHP call 'ini_set'. ;   php_admin_value/php_admin_flag - these directives won't be overwritten by;                                     PHP call 'ini_set'; For php_*flag, valid values are on, off, 1, 0, true, false, yes or no.; Defining 'extension' will load the corresponding shared extension from; extension_dir. Defining 'disable_functions' or 'disable_classes' will not; overwrite previously defined php.ini values, but will append the new value; instead.; Note: path INI options can be relative and will be expanded with the prefix; (pool, global or /usr/local/php); Default Value: nothing is defined by default except the values in php.ini and;                specified at startup with the -d argument;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f www@my.domain.com;php_flag[display_errors] = off;php_admin_value[error_log] = /var/log/fpm-php.www.log;php_admin_flag[log_errors] = on;php_admin_value[memory_limit] = 32M
下面说说出现的错误和一些情况:

nginx connections ,rlimits 跟php-fpm的rlimit_files 的参数配置 要与ulimit -n系统参数的连接数配置一致

如果系统 参数比nginx 设置小的话 会出现 4XX,5xx错误,

还有 就是刚编译好的系统环境 默认ulimit -Sn 参数值只有 1024 个,1024 不能满足NGINX需求 测试并发时候怎么测试到了1024以后就4XX,5XX错误了,最后修改了系统内核参数 为16位 二进制最大数 也就是 65535

failed to ptrace(PEEKDATA) pid 20160: Input/output error
php-fpm的rlimit_files参数 如果比系统的ulimit 小的话出现如上这个ERROR

nginx的参数设置如果比系统ulimit -sn 的参数值小的 话nginx 容易出现 5xx 错误

解决方案就是统一修改 php-fpm.conf,nginx.conf,与系统ulimit -sn 的 参数一致,如果 系统ulimt 的默认参数是1024的话,一定要修改掉他,修改为65535 即可,同时php-fpm,nginx的rlimit 参数也要与其一致……