华为路由器:入门基础命令
程序员文章站
2024-03-20 22:02:16
...
路由器改名
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sysna
[Huawei]sysname route
IP查看
[route]dis ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 4 Routes : 4
Destination/Mask Proto Pre Cost Flags NextHop Interface
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
版本查看
[route]display version
Huawei Versatile Routing Platform Software
VRP (R) software, Version 5.130 (AR1200 V200R003C00)
Copyright (C) 2011-2012 HUAWEI TECH CO., LTD
Huawei AR1220 Router uptime is 0 week, 0 day, 0 hour, 2 minutes
BKP 0 version information:
1. PCB Version : AR01BAK1A VER.NC
2. If Supporting PoE : No
3. Board Type : AR1220
4. MPU Slot Quantity : 1
5. LPU Slot Quantity : 2
MPU 0(Master) : uptime is 0 week, 0 day, 0 hour, 2 minutes
MPU version information :
1. PCB Version : AR01SRU1A VER.A
2. MAB Version : 0
3. Board Type : AR1220
4. BootROM Version : 0
接口信息查看
[route]display interface
Ethernet0/0/0 current state : DOWN
Line protocol current state : DOWN
Description:HUAWEI, AR Series, Ethernet0/0/0 Interface
Switch Port, PVID : 1, TPID : 8100(Hex), The Maximum Frame Length is 1628
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fcca-57aa
Last physical up time : -
Last physical down time : 2020-10-17 16:18:46 UTC-08:00
Current system time: 2020-10-17 16:22:20-08:00
Port Mode: COMMON COPPER
Speed : 100, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec,Record time: -
Output peak rate 0 bits/sec,Record time: -
Input: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Throttles: 0
---- More ----
rip协议
[route]rip
[route-rip-1]q
ospf协议
[route]ospf
[route-ospf-1]q
静态路由
[route]ip route-static
两个路由器相连
一般我们需要添加接口使用的是:2 端口-同异步WAN 接口卡。添加接口卡的时候需要关闭设备
添加完成之后,需要用串口线Serial相连,连接之后路由器上会多出s2/0/0
,s2/0/1
两个接口。
下一篇: Windows安装Redis