欢迎您访问程序员文章站本站旨在为大家提供分享程序员计算机编程知识!
您现在的位置是: 首页

北醒激光模块TFmini——STM32驱动程序(STM32F103C8T6)

程序员文章站 2022-06-09 09:28:44
...

背景:该激光模块属于精度比较高的激光测距模块,使用方便。

代码地址:https://github.com/W-yt/YuTian_Pro/tree/master/TFMini_Driver

平台:

硬件:STM32F103C8T6

通信:串口3与激光模块通信;串口1用于输出距离信息(到串口助手)

硬件连接:

北醒激光模块TFmini——STM32驱动程序(STM32F103C8T6)

串口配置:(采用串口接收中断 尝试DMA接收时发现无法进入串口空闲中断)

void vUart3Config(void)
{  
  GPIO_InitTypeDef 	GPIO_InitStructure;
  USART_InitTypeDef USART_InitStructure;
  NVIC_InitTypeDef 	NVIC_InitStructure;
  DMA_InitTypeDef		DMA_InitStructure;
	 
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);

  //USART3_RX	  GPIOB.11		(using)
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(GPIOB, &GPIO_InitStructure);  

  //USART3_TX   GPIOB.10
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOB, &GPIO_InitStructure);

  USART_InitStructure.USART_BaudRate = 115200;
  USART_InitStructure.USART_WordLength = USART_WordLength_8b;
  USART_InitStructure.USART_StopBits = USART_StopBits_1;
  USART_InitStructure.USART_Parity = USART_Parity_No;
  USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
  USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

  USART_Init(USART3, &USART_InitStructure);
  USART_ITConfig(USART3, USART_IT_RXNE, ENABLE);
  USART_Cmd(USART3, ENABLE); 
	
  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);  
	
  NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
	
//	//DMA——RX
//	USART_DMACmd(USART3,USART_DMAReq_Rx,ENABLE);
//	
//	DMA_DeInit(DMA1_Channel3);
//	DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)(&(USART3->DR));
//	DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)USART3_DMA_rece_buffer;
//	DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
//	DMA_InitStructure.DMA_BufferSize = USART3_DMA_rece_buffersize;
//	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
//	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
//	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
//	DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
//	DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
//	DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;
//	DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
//	DMA_Init(DMA1_Channel3,&DMA_InitStructure);

//	NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel3_IRQn;           
//	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;          
//	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1; 
//	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
//	NVIC_Init(&NVIC_InitStructure);
//	
//	DMA_ITConfig(DMA1_Channel3,DMA_IT_TC,ENABLE);
//	
//	DMA_Cmd(DMA1_Channel3,ENABLE);
}

串口中断:

uint8_t temp_data = 0;
uint8_t TFmini_low,TFmini_high = 0;
uint8_t flag = 0;
void USART3_IRQHandler(void)
{
	if(USART_GetITStatus(USART3,USART_IT_RXNE) != RESET)
	{
		temp_data = USART_ReceiveData(USART3);
		
		if((temp_data == 0x59) && (flag == 0))
		{
			flag = 1;
		}
		else if((temp_data == 0x59) && (flag == 1))
		{
			flag = 2;
		}
		else if(flag == 2)
		{
			TFmini_low = temp_data;
			
			flag = 3;
		}
		else if(flag == 3)
		{
			TFmini_high = temp_data;
			
			distance = ((uint16_t)TFmini_high<<8) | ((uint16_t)TFmini_low);
			
			printf("receive once:  %d cm \r\n",distance);
			
			flag = 0;
		}
	}
}

 

——cloudos

——2020/3/31

 

 

 

 

 

 

 

 

 

 

 

 

 

 

相关标签: STM32基础 驱动