linux 路由表设置 之 route 指令详解
程序员文章站
2022-06-02 18:42:39
...
使用下面的 route 命令可以查看 Linux 内核路由表。
默认情况下,route会去找出该IP的主机名称,如果找不到,就会显得有点迟钝,所以通常使用route -n。
[[email protected] ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.236.46.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.202.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.61.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.95.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.6.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.101.0 * 255.255.255.0 U 0 0 0 eth0
10.236.69.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.23.0 * 255.255.255.0 U 0 0 0 eth1
10.236.53.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.232.21.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.51.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
169.254.0.0 * 255.255.0.0 U 0 0 0 eth1
default 10.236.101.254 0.0.0.0 UG 0 0 0 eth0
[[email protected] ~]# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.236.46.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.202.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.61.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.95.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.6.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.101.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
10.236.69.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.23.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1
10.236.53.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.232.21.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
10.236.51.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1
0.0.0.0 10.236.101.254 0.0.0.0 UG 0 0 0 eth0
route 命令的输出项说明
输出项 说明
Destination 目标网段或者主机
Gateway 网关地址,”*” 表示目标是本主机所属的网络,不需要路由
Genmask 网络掩码
Flags 标记。一些可能的标记如下:
U — 路由是活动的
H — 目标是一个主机
G — 路由指向网关
R — 恢复动态路由产生的表项
D — 由路由的后台程序动态地安装
M — 由路由的后台程序修改
! — 拒绝路由
Metric 路由距离,到达指定网络所需的中转数(linux 内核中没有使用)
Ref 路由项引用次数(linux 内核中没有使用)
Use 此路由项被路由软件查找的次数
Iface 该路由表项对应的输出接口
3 种路由类型
主机路由
主机路由是路由选择表中指向单个IP地址或主机名的路由记录。主机路由的Flags字段为H。例如,在下面的示例中,本地主机通过IP地址10.236.101.254的路由器到达IP地址为10.236.202.116的主机。
Destination Gateway Genmask Flags Metric Ref Use Iface
10.236.202.116 10.236.101.254 255.255.255.255 UGH 0 0 0 eth0
网络路由
网络路由是代表主机可以到达的网络。网络路由的Flags字段为N。例如,在下面的示例中,本地主机将发送到网络10.236.46的数据包转发到IP地址为10.236.23.251的路由器。
Destination Gateway Genmask Flags Metric Ref Use Iface
10.236.46.0 10.236.23.251 255.255.255.0 UG 0 0 0 eth1
默认路由
当主机不能在路由表中查找到目标主机的IP地址或网络路由时,数据包就被发送到默认路由(默认网关)上。默认路由的Flags字段为G。例如,在下面的示例中,默认路由是IP地址为10.236.101.254的路由器。
Destination Gateway Genmask Flags Metric Ref Use Iface
default 10.236.101.254 0.0.0.0 UG 0 0 0 eth0
配置静态路由
route 命令
设置和查看路由表都可以用 route 命令,设置内核路由表的命令格式是:
# route [add|del] [-net|-host] target [netmask Nm] [gw Gw] [[dev] If]
其中:
add : 添加一条路由规则
del : 删除一条路由规则
-net : 目的地址是一个网络
-host : 目的地址是一个主机
target : 目的网络或主机
netmask : 目的地址的网络掩码
gw : 路由数据包通过的网关
dev : 为路由指定的网络接口
route 命令使用举例
添加到主机的路由
# route add -host 10.236.202.116 dev eth0
# route add -host 10.236.202.116 gw 10.236.101.254 #添加到10.236.101.254的网关
添加到网络的路由
# route add -net 20.236.50.0/24 gw 10.236.23.251
# route add -net 20.236.50.0 netmask 255.255.255.0 eth0 #添加20.236.50.0的网络
# route add -net 10.236.202.0 netmask 255.255.255.0 gw 10.236.101.254 #添加10.236.202.0的网络
# route add -net 192.168.1.0/24 eth1
添加默认路由
# route add default gw 10.236.101.254
删除路由
# route del -host 192.168.1.2 dev eth0:0
# route del -host 10.236.202.116
# route del -host 10.20.30.148 gw 10.20.30.40
# route del -net 20.236.50.0/24 eth0
# route del -net 20.236.50.0/24
# route del -net 10.20.30.40 netmask 255.255.255.248 eth0
# route del -net 10.20.30.48 netmask 255.255.255.248 gw 10.20.30.41
# route del -net 192.168.1.0/24 eth1
# route del default gw 192.168.1.1
在linux下设置永久路由的方法:
1.在/etc/rc.local里添加
方法:
route add -net 10.236.51.0/24 gw 10.236.23.251
route add -net 10.236.202.0/24 gw 10.236.23.251
route add -net 10.236.95.0/24 gw 10.236.23.251
route add -net 10.236.6.0/24 gw 10.236.23.251
route add -net 10.236.53.0/24 gw 10.236.23.251
route add -net 10.236.46.0/24 gw 10.236.23.251
2.在/etc/sysconfig/network里添加到末尾
方法:GATEWAY=gw-ip 或者 GATEWAY=gw-dev
3./etc/sysconfig/static-router :
any net x.x.x.x/24 gw y.y.y.y
下一篇: CentOS7初始化配置