【Apache+tomcat+mod_jk 实现负载均衡】

安装环境简介
本次使用三台服务器，其中安装Apache作为负载均衡转发，另外两个tomcat模拟应用服务器。

(集群早在2013年就研究过，那时候在WinXP上面研究，参考文档如下：https://yunpan.cn/crcYiCPKrkJ82  访问密码 0e99)
Apache 192.168.1.113
tomcat:192.168.1.106/192.168.1.109

步骤一、安装Tomcat
    tomcat安装在此省略，先安装JDK，配置JAVA_HOME环境变量，然后下载解压tomcat

步骤二、安装Apache
[root@node1 opt]# mkdir -p  /usr/local/apache2/
[root@node1 opt]# tar -zxvf httpd-2.2.23.tar.gz
[root@node1 opt]# cd httpd-2.2.23
[root@node1 httpd-2.2.23]# ./configure --prefix=/usr/local/apache2/ --enable-module=most --enable-shared=max --enable-so
[root@node1 httpd-2.2.23]# make
modules/http/.libs/libmod_http.a(byterange_filter.o): In function `ap_set_byterange':
byterange_filter.c:(.text+0x12c1): undefined reference to `apr_array_clear'
collect2: ld returned 1 exit status
make[1]: *** [httpd] Error 1
make[1]: Leaving directory `/opt/httpd-2.2.23'
make: *** [all-recursive] Error 1

解决方案
[root@node1 httpd-2.2.23]# make clean
[root@node1 httpd-2.2.23]# ./configure --prefix=/usr/local/apache2   --enable-mods-shared=most  --with-included-apr
[root@node1 httpd-2.2.23]# make
[root@node1 httpd-2.2.23]# make install  
测试apache服务器
/usr/local/apache2/bin/apachectl –k start|stop|restart  分别为启动 停止 重启

步骤三、负载均衡配置
1、上传文件
 /usr/local/apache2/modules/mod_jk-1.2.23-apache-2.2.x-linux-x86_64.so

2、配置负载均衡文件
 /usr/local/apache2/conf/workers.properties
 worker.list = controller,tomcat1,tomcat2  #server 列表
  #========tomcat1========
  worker.tomcat1.port=8009         #ajp13 端口号，在tomcat下server.xml配置,默认8009
  worker.tomcat1.host=192.168.1.106  #tomcat的主机地址，如不为本机，请填写ip地址
  worker.tomcat1.type=ajp13
  worker.tomcat1.lbfactor = 1   #server的加权比重，值越高，分得的请求越多
  #========tomcat2========
  worker.tomcat2.port=8009       #ajp13 端口号，在tomcat下server.xml配置,默认8009
  worker.tomcat2.host=192.168.1.109  #tomcat的主机地址，如不为本机，请填写ip地址
  worker.tomcat2.type=ajp13
  worker.tomcat2.lbfactor = 1   #server的加权比重，值越高，分得的请求越多

  #========controller,负载均衡控制器========
  worker.controller.type=lb
  worker.controller.balanced_workers=tomcat1,tomcat2   #指定分担请求的tomcat
  worker.controller.sticky_session=1

注意：work端口对应Tomcat的server.xml文件标红色部分端口

<Connector port="8080" protocol="HTTP/1.1"   connectionTimeout="20000"  redirectPort="8443" />
 <!-- Define an AJP 1.3 Connector on port 8009 -->
  <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" />

 3、新建文件 mod_jk.conf 添加相关内容
LoadModule jk_module modules/mod_jk-1.2.23-apache-2.2.x-linux-x86_64.so
JkWorkersFile conf/workers.properties
JkMount /* controller
把新建的mod_jk.conf文件添加到/usr/local/apache2/conf/目录下面

 

4、修改/usr/local/apache2/conf/httpd.conf文件
在文件末尾加上include "/usr/local/apache2/conf/mod_jk.conf"
即如下所示：
  include "/usr/local/apache2/conf/mod_jk.conf"
"/usr/local/apache2/conf/httpd.conf" 465L, 15985C written

步骤四、测试负载均衡
http://192.168.1.113/

 

 

 另一实现负载均衡方式参考：nginx+tomcat实现负载均衡

永久链接: http://gaojingsong.iteye.com/blog/2267299

  

[root@node1 logs]# tail -f mod_jk.log
[Tue Jan 19 14:29:39 2016] [24407:52512] [info]  ajp_service::jk_ajp_common.c (1902): (tomcat2) receiving from tomcat failed, recoverable operation attempt=0
[Tue Jan 19 14:29:39 2016] [24407:52512] [info]  ajp_service::jk_ajp_common.c (1941): (tomcat2) sending request to tomcat failed,  recoverable operation attempt=1
[Tue Jan 19 14:48:14 2016] [24762:52512] [info]  ajp_connect_to_endpoint::jk_ajp_common.c (876): Failed opening socket to (192.168.1.109:8009) (errno=111)
[Tue Jan 19 14:49:03 2016] [24765:52512] [info]  ajp_connect_to_endpoint::jk_ajp_common.c (876): Failed opening socket to (192.168.1.106:8009) (errno=111)
[Tue Jan 19 14:49:11 2016] [24766:52512] [info]  ajp_send_request::jk_ajp_common.c (1244): (tomcat2) increase the backend idle connection timeout or the connection_pool_minsize
[Tue Jan 19 14:49:11 2016] [24766:52512] [info]  ajp_service::jk_ajp_common.c (1941): (tomcat2) sending request to tomcat failed,  recoverable operation at